Single Blog Title

This is a single blog caption

B&G Crane Uses Hydra-Slide System for Exchanger Replacement

B&G Crane Service LLC utilized a 300-ton capacity Hydra-Slide HT300 heavy-track hydraulic skidding system and other equipment to remove and replace two heat exchanger units for a project in Calcasieu, Louisiana recently.

The full scope of work included removal and replacement of five exchangers; two were atop a 51 ft.-high structure elevation and removed by crane, while the smallest unit was moved using skates. The HT300 was used to slide the old exchangers, weighing 49,000 lbs. and 59,000 lbs., a distance of 60 ft. before repeating the process in reverse with the replacement units that weighed 58,000 lbs. and 66,000 lbs.

The standard HT300 package comes complete with load-bearing track, four skid shoes, push cylinders and all connecting hardware. The load-moving solution needs minimal clearance and has a total height of only 7 in. (180mm). Additional skid track sections were supplied by Hydra-Slide on short notice to extend the 50 ft. of double track that B&G had available. They connect with a simple lug and pin set and could have been leap-frogged to slide longer distances, if a requirement arose.

The equipment combined with other lifting technologies, including two Liebherr mobile cranes—a 100t capacity five-axle LTM 1100-5.2 and a 500t capacity eight-axle LTM 1500-8.1. B&G also utilized a J&R Engineering Lift-n-Lock 1400 series hydraulic gantry and two Scheurle self-propelled modular transporters (SPMT), of six and 12 lines respectively.

B&G utilized a 300-ton capacity Hydra-Slide HT300 heavy-track hydraulic skidding system.

Mark Morris, rigging superintendent at B&G Crane, explained that the first stage of the project was removal of the existing exchangers using the LTM 1500-8.1. He added: “At that point, grating from the elevation was opened up to allow rigging to be lowered through the existing floor. The exchangers were then blocked up with cribbing to allow installation of the Hydra-Slide tracks before they were lowered onto the skid shoes.”

Additional skid track sections were supplied to extend the 50 ft. of double track provided as standard.

Once the exchangers had been skidded clear of the site, the LTM 1100-5.2 lifted them onto the SPMTs, for transportation to a lay-down area. Morris said: “The process was completed in four, 12-hour shifts, which included all the required rigging, setup, removal and installation work.”

The exchangers were blocked up to allow installation of the Hydra-Slide tracks before they were lowered onto the skid shoes.

Extra safety measures were implemented in the planning stages to allow for elevated work on false work platforms, which were essentially barge ramps created by fabricating hand rails to OSHA specifications. Morris explained that the solution prevented potential fall and drop-related accidents from height.

The new exchangers were installed in the same position as the older units.

“The safety mantra on the project aligned well with the Hydra-Slide equipment,” Morris continued. “Safe and controlled movement of the loads on the elevated platforms not only provides for smooth operation and minimal labor intensity, but also gives clients added confidence in our execution of work. We have used the Hydra-Slide equipment on several projects over the last four years since I have been with the company and I look forward to applying it on many more.”

The HT300 was used to slide the exchangers 60 ft.

1 Response

  1. Really a very helpful article thanks for sharing and keep on sharing!
    ABCO Engineers is the Largest Crane Suppliers In Bangalore,Mangalore, Belgaum. Abco Engineers are the best EOT Crane Manufacturers in Bangalore,Karnataka. ABCO provides Cranes with Excellent Quality and the Wide Range of Crane services in Bangalore,Mangalore, Belgaum.Contact today for CompleteCrane services in Bangalore
    karnataka.
    Read more: https://www.abcoengineers.com/

Leave a Reply

Please send news and information on new products to: [email protected]